Nambour 07 54762899 | Noosaville 07 54424833 sales@soundinmotion.com.au

Alpine PDR-F50 4 chl Digital Amplifier

$549.00

Sound In Motion – Authorised Alpine Electronics Australia – Dealer, Stockist and Installation centre.

 

 

Description

Alpine PDR-F50

4 chl Digital Amplifier

For tremendous power at all levels, with hard-hitting bass

The fully digital Alpine PDR-F50 4-Channel Amplifier provides powerful bass, big dynamic sound, non-shutdown performance, and easy vertical or horizontal installation.

Power

  • 14.4V 4ohm: 4 x 85W
  • 14.4V 2ohm: 4 x 125W

Each Alpine PDR-F50 amplifier is unmatched in its class for power density performance (watts per cubic cm) and damping factor.

The Alpine PDR-F50 Power amplifier offers the best performance in their class, redefining expectations in the high-power compact amplifier category.

Thanks to trickle-down technology, Alpine’s in-house engineering team has taken many of the patent-pending technologies introduced in the industry-leading PDX series and infused them in the new PDR-Power amplifiers.

The Alpine  PDR-F50 Power amplifier provides you with the absolute widest bandwidth, best signal-to-noise, lowest distortion and highest damping factor of any amplifier in their class without sacrificing power.

Dual-Feedback Modulation Loop

When playing music, a clean, distortion-free, low-power signal input to an amplifier should exit as an identical high-power output signal to drive your speakers. In reality, most amps don’t even come close to this ideal, instead adding significant audible distortion especially in the high frequencies, earning typical Class-D amplifiers a deserved reputation for bad sound. The PDR-Power’s Global Modulation with Adaptive Feedback Control loop circuitry intelligently assures the power output is as clean and distortion-free as possible. Their real-time error-correction analyzes the signal not only once, but twice by comparing input signal with the output throughout the entire amplification process. In doing so, PDR-Power amplifiers ensure that their output signal delivers a clean, clear and powerful sound that must be heard to be believed.

Small, Powerful Design

  The new PDR-Power series amplifiers have decreased in size compared to the X-Power, yet they pack in much more flexibility, durability with Alpine sound quality.

Unequaled Reliability

Excessive heat is the enemy of amplifiers and under extreme conditions will result in most amps shutting down completely. PDR-Power amps use a special Multi-Stage Power Management circuit that continuously monitors critical component temperatures throughout the amplifier and decreases power output if anything gets too hot. If you are playing music under heavy loads for long periods, the circuit automatically reduces power output slightly at first, and then further in a second stage if necessary. This two-stage approach provides seamless, interruption free listening experience for non-stop music playback.

Standing Alone in the Clarity Class

Ultra-Wide Frequency Bandwidth:
This super-wide, industry leading frequency range offers listeners unparallel sound quality and detail that bests even the most high-end audiophile equipment.

Best Signal-to-Noise:
In order to ensure that all of the industry-leading sound quality is heard at your ears, we’ve worked to create a platform that offers an unbelievably low noise floor, taking extra care to ensure a clean signal path, with no extraneous inferences.

Low Distortion:
PDR-Power amps offer extremely wide and linear frequency response that results in unparalleled musical detail. Extremely low distortion means pure musical performance without audible artifacts to destroy your sound experience. Additionally, these amps have extremely high stereo separation and smooth phase response, which means more dynamic realistic imaging and staging for your total musical enjoyment. On the Mono side, best-in-class low distortion and tight control will give you clean, accurate bass response.

Highest Damping Factor:
With ultra-low output impedance, the new PDR-Power offers extremely controlled, tight bass for unprecedented sound quality. Damping Factor ratings are >1300 for Mono and >500 for full range models.

Sharper -24dB/octave slope:
Ensuring that your sub plays longer, accurate and cool the PDR-M65 / PDR-V75(Subwoofer Channel) has a -24dB octave slope in the built-in low pass filter. A sharper slope to the subwoofer allows only the desired low-end frequencies play through your subwoofer.

All Digital Lineup

classd The PDR series uses much of the same digital technology as the PDX series, achieving high efficiency with excellent audio performance, including low distortion, high damping factor and high S/N ratio

 

Awesome Power Density, Digital Sound Quality

  The PDRF50 amplifier is unmatched in its class for power density performance (watts per cubic cm) and damping factor.

You get tremendous power at all levels, with hardhitting bass. S/N ratios and frequency response are also outstanding.

Bass EQ

basseq

Bass EQ provides a boost at 40Hz to increase the impact of sound from the subwoofer.

 

Crossover

crossoverHigh Pass (HP) Crossover for better sound. The high pass crossover cuts bass frequencies sent to the speaker outputs and the full-range pre-outs.

Suited for subwoofer systems, the HP filter enables speakers to perform more efficiently within their reproduction range and limits bass response cancellation.

 

Proven Power—Certified From Birth

All PDR-Power amplifiers are individually tested and have certified power ratings. Each amp comes with their very own verification certificate documenting its actual power output exceeds the rating by a wide margin.

Rotatable Illuminated Alpine Badge

  PDR-Power amplifiers come with a rotatable illuminated badge that makes a very attractive presentation when mounted vertical or horizontally.

Topside Controls and Adjustments

  Topside controls on top of the PDR-F50 Power amplifier makes installation and tuning easier than its predecessors.

Just unscrew two fasteners and you’ll have access to all the controls needed to tune the amplifier.

Their small size and versatile controls allow the PDR-Power amplifiers to easily be added to either an aftermarket or factory system and can be setup to accommodate a variety of system configurations.

Alpine PDR-F50 – Features

  • Install

    • Angled Insert-Type Terminals
    • Integrated Wire and Mounting Screw Terminals
    • Terminal Layout: One-Sided
    • Mounting Design: Clean-look installation

    General

    • Rotatable Illuminated Alpine Badge
    • Top-Side Control Panel
    • Amplifier Type: Class-D (Digital)
    • Channel Design: 4/3/2 Channel
    • Thermal Control : Thermal management control
    • Low-battery Protection
    • Power Supply: Resonant Mode Power Supply
    • Power Supply Design: DC-DC PWM Power Supply
    • Board Circuitry: STAR Circuit
    • Current Protection: Auto Over-Current Protection
    • Power Indicator: Top Mounted Blue LED Power/Status Indicator (Power: Blue, Status: Blue/Red)
    • Crossover: Adjustable Low-Pass/High-Pass
    • Pre-Amp Stage: Discrete
    • Final Outputs: MOSFET
    • Board Design: 6-Layer Glass Epoxy PC Board
    • Gain Control: Adjustable

    Alpine PDR-F50 – SPECIFICATIONS

    Max Power Output Ratings

    • Total Max Power: 1000W

    RMS Power Ratings

    • Per channel into 4 Ohms: (@14.4V ?1%THD+N) 85W x 4
    • Per channel into 2 Ohms: (@14.4V ?1%THD+N) 125W x 4
    • Bridged into 4ohms, 14.4V(@14.4V ?1%THD+N): 250W x 2

    Sound Tuning

    • Crossover: Variable LPF, 50-400Hz (-12dB / oct )
    • Crossover: Variable HPF, 50-400Hz (-12dB / oct )
    • Equalizer (Bass EQ): 0 or +6 or +12dB (CH3/4, fc=50Hz) Selectable

    Dimensions

    • Heat Sink (WxHxD) mm: 228.5mm x 165mm x 50.8mm

    General

    • Power Requirements: 14.4V DC (11 – 16V)
    • Input Sensitivity (RCA Input): 0.2 – 4.0V
    • Input Impedance: >10k ohms
    • Frequency Response (+0, -3dB: 1W into 4 ohms): 8Hz – 45kHz
    • Frequency Response (+0, -1dB: 1W into 4 ohms): 10Hz – 30kHz
    • THD+N (10W into 4 ohms): ?0.02%
    • THD+N (Rated Power into 4 ohms): ?0.07%
    • Damping Factor (10W into 4 ohms at 100Hz): >500
    • Signal to Noise (Rated Power into 4 ohms): >106dB
    • Weight: 2.5kg

Sound In Motion – Home Of Alpine on the Sunshine Coast – Authorised Premium Alpine Electronics Australia Dealers, Stockists, Installation Centres

* 1 Year Warranty as per Alpine Electronics Australia Terms and Conditions